Electrostatic film is a special type of substance sticks to the surface without any adhesive. It is very helpful because it helps in decorating, protecting our windows and also protects private spaces from the eyes. But as is the case, sometimes we need to cut certain film in specific dimensions or shapes so that they can be perfectly aligned with our requirements. So, can we do that? Yes, we absolutely can!

​

How to Make It Fit Your Needs

Before we begin cutting the electrostatic film, it is very important to measure the area that we want this product covers. To do this, we use a ruler or measuring tape to determine the height and width of the surface. After all, with those measurements in hand we can specify the size of electrostatic film to be cut that will keepfood fresh well.

For instance, if we need to cover a window that shaped like square then select an electric self adhesive pet film which is also of exact same situation but just bigger in size as the screen itself. This way there will be no gaps. If, on the other hand, we need to coat a round table that will choose cast circular sheet of film with electrostatics over an diameter greater than the tabletop. When needed, we do trim the film to ensure it is a perfect fit.

The Cutting Steps

Electrostatic Film Cut The size of the film cut is not too difficult, but we still need to be careful. The following is a brief summary for how to properly cut and resize your electrostatic film.

Prepare your tools: To get started you will need some critical tools Have ready a good sharp pair of scissors, pencil, ruler and cutting mat.

Step 2: Mark the film - Now we need to mark where you want it cut. Use pencil and ruler to draw cut lines on the film-side of films without selfadhesive pet film. Depending on what you whant, you can make simple lines or shapes.

Trim the film: This is where you get to cut. Cut along where you marked them using the scissors. NOTE: Be sure to take this slow and easy, the slower you cut, the easier it will be for you to stay on your line.

Install the film: as long as you completed step 2 and cut your window tint to size & shape, simply remove (release) it from its backing. Now put film on surface you want to cover. Lay it flat with no air pockets or creases. This will make it look less cluttered and more professional.

How to Cut Electrostatic Film

You can still follow these steps but here are a few more tips that will make your life easier and cut the process by half with just large electrostatic film sheets:

First measure and mark the area you want to cover On power lines, then about how to set with a pencil and ruler. Masking tape can also help keep the selfadhesive vinyl film in place so it doesn't slide around as you're cutting.

Get a template: Better still, if you want this to be really easy then make yourself a paper or cardboard cut-out of the surface you plan on covering. The last step is making a template of your sticker, transfer it to the electrostatic film and then cut along those lines.

Back Sided Cut: When you cannot get the proper shape with a usual cut, flip the film and place it onto your cutting mat face to back. After transferring your design, cut along the lines with a craft knife or box cutter using no 11 blades. Put slight pressure, and stay in the lines.

Trim off the excess, smooth out any loose edges with a fine grit sandpaper or even your nails of course! And it will help the film lay better and appear much tighter.

Additional Advice for Trimming Electrostatic Film

It is difficult in some ways to cut electrostatic film, so if you need a more accurate cutting method, the iridocs laser polarimeter cuts evenly and finely. Here are a few tips:

Sharp scissors: You should always keep your scissor sharp. Scissors that arent sharp can shred the film and give you ragged cuts notably hard to look at.

Do not pull the film: The electrostatic film is a flexible material and if you stretch it too much or you apply more pressure than necessary, this will cause the stretched out substance to change shape.

Step 2: Cut Slowly And Carefully ~ This step of cutting slow and careful is a very crucial point to take notice. The big problem with rushing is that it can cause you cut hair unevenly or worse, accidentally hold your child's skin in one part while trying to make an escape.

Start cutting with scrap: Then, when you get to the big (or expensive) electrostatic sheet, start there. This helps you to test your inabilities and cutting techniques before making any experiment with the larger slice.

Getting the Perfect Fit

These are the main things that should consider when cutting electrostatic film for a perfect fit:

Measure the surface well: Now is not the time to be sloppy in this size or shape. This will help you in selecting the proper size and form of electrostatic film.

If the film has a pattern such as stripes, lining or design, ensure that it is applied down straight and in line with your surface (this goes double for designs which repeat).

TOP TIP - Adhesive side: Remember always to cut the non-adhesive side of the film. Leave some extra space for margins or overlaps if needed.

Methods and Skills: Sharp. Take the time to work with nicely sharpened tools which will make your task easier, there are so many cutting techniques that can be used for whittling in this project use those method you feel comfortable at doing

With these more reliable cutting methods, you can barely cope with any Anti Static Film roll size or shape. Holistically, you can enjoy its multiple perks from enhancing appearance to attaining protection and privacy. Happy cutting!